UK-POLOS.NET - THE VW Polo Forum

When I close the pq25 programmer I get the following log..

Opening communication with ecu...
Reading identification...
ECU: 7H0937090 J519 BCM PQ25 MAX4
Opening communication with ecu...
Reading identification...
Reading data...
Sending seed request...
SEED received.
Error entering security mode

I have got my vag can pro.
I can connect to bcm and see the coding etc. There do not appear to be any label files for the amarok though.
I can enter adaption and see the same as vcds (again, no label file in vcp)

If I try to use the PQ25 programmer I get an error and It will not connect to the bcm?

Just a quick update,
I have ordered a vag can pro which I am still waiting for.
If I can't get any further with that I will look into swapping the bcm.

Looking at my adaptions map, I don't have any values set from the factory to 100.
The highest value I have (unidentified) is ch37 with a value of 80.
(ch60 & ch61 have values of 200 but these seem to be releated to the alarm sensors (tilt & ultrasonic sensitivity)

II have read some information on ...

ok, I will try to find the correct ecu.
I think Differential Lock and Transfer box are only mechanical. I will look at this in more detail.
Ideally I will replce with a current Amarok bcm as it would be the best oem way.

I will see the dealer and find a price for a new one and look for used units ...

Testing has stopped as I can not locate my scope. I think it has been lent to somebody.
All I can confirm with using a DMM on the headlight connector is that: (all this has been done without engine running)
With only DRL Led on - Pin 4 & Pin 10 have 12.2v
In any condition when the DRL should be ...

Once I have thoroughly reviewed all the Amarok wiring diagrams from 2009 to the present ... (yes, all of them, both eRwin and Elsawin) I can state the following.
Thank you for the time you spend on this!! I did look at wiring diagrams many times but it is my first time with vw wiring so good to ...

The headlights came with 4G0907697G drivers for the leds. (there is another ballast for the xenon bulbs)
I looked on the parts and it suggests it sholud be 4G0907697F for Amarok. I have purchased 1 of these as a test and it works the same as the others. (currently I have the 'G' installed in one ...

Here is autoscan with changed coding:

Address 09: Cent. Elect. (J519) Labels: 7H0-937-08x-09.clb
Part No SW: 7H0 937 090 HW: 7H0 937 090
Component: BCM PQ25 Max4 H72 0706
Revision: B9072001 Serial number: 0531 125120572
Coding: 240002386C61140093380E316C8B96DD0F80654E608430D1300000030003 ...

So with that coding everything stays the same (still no sidelights or dimming drl) except I get the bulb warning light on the dash.

If I then change byte 23 bit 1 still the same but I have no high beam shutter. (It does work if I pull the stalk for flash)

The BCM is the original that was factory ...

The headlights came with 4G0907697G drivers for the leds. (there is another ballast for the xenon bulbs)
I looked on the parts and it suggests it sholud be 4G0907697F for Amarok. I have purchased 1 of these as a test and it works the same as the others. (currently I have the 'G' installed in one ...

Hello,
Many thanks for the help.
I have been reading posts from you guys and you are the best!!
Autoscan here:

Saturday,12,August,2017,08:50:02:04550
VCDS -- Windows Based VAG/VAS Emulator Running on Windows XP x86
VCDS Version: 15.7.0.2
Data version: 20150820
www.Ross-Tech.com


VIN ...

Hi all,
I know this is not a polo but there seem to be a few xenon experts on here!!

I have just fitted a pair of oem bi-xenon's (2016 lights) with led drl into a 2012 (MY13) Amarok Highline. (this truck came with the 'auto' lights switch & rain sensor fitted.)
Previous mods include oem reverse ...