UK-POLOS.NET - THE VW Polo Forum

Hello, and a Happy New Year to you all. I just wanted to say hello and say thank you again to Ciclo and all that have contributed to this thread without your help I would not have been able to carry out these modifications. I am pleased to report that my installation, which by no means was done quic...

Hi Ciclo, Very pleased to say, we have success :D :D :D I had the terminals in the front sensor plug in the wrong locations :oops: scan - Saturday,24,October,2020,15:01:25:03258 VCDS -- Windows Based VAG/VAS Emulator Running on Windows 10 x64 VCDS Version: 20.4.2.0 (x64) HEX-V2 CB: 0.4513.4 Data ver...

Hi Ciclo, Thanks for your reply.. I have put in that code and entered the security access, it has not enabled me to run basic settings and the fault code reappears right after after they are erased. The chassis is correct as far as I can work out. It is the only choice for AWD (4wd). I changed this ...

Hi folks, So, the new clutch has been fitted and the van has moved under its own steam for the first time since June :D Level sensors are fitted but I cant seem to clear the fault codes for it. I have attempted to run basic settings but have been unable to do so. VCDS shows an error message (which I...

Hi reido80, According to ETKA it is 4H0973712A https://seat.7zap.com/images/Tnrpics/4H0973712A.jpg https://i.imgur.com/RohX2bY.jpg ...although it seems identical to 4B0 ... ... A https://i.ebayimg.com/images/g/6x4AAOSwLVZV6syB/s-l1600.jpg Thank you very much for the explanation and images.👌 Cool, I...

Ordered the correct plugs, part number 4B0973712A

Ok, so I have ran the wiring for the rear xenon level sensor. Goes from the Xenon level control module under dash/BCM area - up drivers A pillar, follows wiring loom along the roof line - at D pillar it drops down and follows wiring loom for Rear speed sensor, through a grommet with a helpfully spar...

Hi ciclo, hope you are well, Many thanks for all your help, The lights, rain sensors, Wipers etc all look to work well. Here we have the latest scan, The van is still sat in the same place it has been for 2 months or so due to the Clutch slave cylinder giving in so I have not given anything a proper...

So after a charge and a reset of DTC codes the trailer fault in can gateway has gone, hopefully it was just because it had been disconnected and reconnected etc. The centre brake light fault is corrosion in the plug so a new light and T2 plug has been ordered. I have still to determine the best rout...

still no level sensors plugged in, running the rear wiring just now. RLS and mirror unplugged. Trailer module plugged in to test Reverse wire between t73b/12 and under seat plug now done. old pin isolated. Edit* Just checked battery voltage and it is low so going to give it a charge. Edit2* The brak...

Yes, just now there are no level sensors connected. Still to wire in reverse wire between bcm and green plug. Other parts like trailer electrics will be plugged back in when seats go back in. ( i will actually plug that in tomorrow to test the fault code goes away) Roof harness very much still hangi...

New scan - Sunday,30,August,2020,18:07:46:03258 VCDS -- Windows Based VAG/VAS Emulator Running on Windows 10 x64 VCDS Version: 20.4.2.0 (x64) HEX-V2 CB: 0.4513.4 Data version: 20200730 DS317.0 www.Ross-Tech.com VIN: WV2ZZZ7HZDH0 License Plate: TEST4 Mileage: 130870km-81318mi Repair Order: ----------...

Ahh, I see what you mean, that makes sense. I was wondering if it was because my electrics perhaps differed because I had Trailer electrics. I will run that wire then so it is also CAN controlled. I am having a bit of trouble working out what I am supposed to do with the W8 light and the anti dazzle...

Thanks, that's what I will do then..perfect. The Kufatec RLS harness instructions are telling me to wire in the Rain sensor pin3 to BCM T73b/33, however the wiring diagrams are showing to wire this in with the purple/yellow lin circuit that goes to T73b/24. (which I can connect to in various places)...

Nice one Ciclo, many thanks, I have another ALWR module on its way, supposedly from a T5, so will give that a try and sell the current one. I have tested both lights now and everything seems to be good. I am going through all the redundant wiring to see what is live still. I have noticed that the ol...