ciclo. Wife's Golf MK7.5 Ready2Go 1.0 TSI 6MT 200Nm/l 115HP

A section of the forum for members to show off their non-polo vehicles.
User avatar
ciclo
Bling Bling Diamond Member
Posts: 6147
Joined: Sun Feb 24, 2013 10:20 am
Drives: 6R Rline/G7.5/Touareg Rline'19/T-Cr'20
Location: Earth ♥, Spain ☼
Contact:

Re: ciclo. Wife's Golf MK7.5 Ready2Go 1.0 TSI 6MT 200Nm/l 115HP

Post by ciclo »

Mart!n-GTI-DK wrote: Tue Jan 12, 2021 7:52 pm Hey Ciclo. Am I so lucky that you happen to know which mal and female pins I need for the plug fra the A pillars to the front doors in the mk7?
Image

Image

:arrow: https://www.a4-freunde.com/showwiki.php ... uebersicht


https://www.uk-polos.net/viewtopic.php?p=575519#p575519
User avatar
ciclo
Bling Bling Diamond Member
Posts: 6147
Joined: Sun Feb 24, 2013 10:20 am
Drives: 6R Rline/G7.5/Touareg Rline'19/T-Cr'20
Location: Earth ♥, Spain ☼
Contact:

Re: ciclo. Wife's Golf MK7.5 Ready2Go 1.0 TSI 6MT 200Nm/l 115HP

Post by ciclo »

New fuses and connections for the installation of 8IU LED headlights.

New fuses

Previous info :arrow: viewtopic.php?p=577138#p577138

Installing the new fuse holder (4 fuses) is easy but a very hard task. :)
- To insert the fuse holder into the parking unit bracket a pliers are required.
Image
Note: I have quite a bit of strength in my hands 🐒, but it was impossible for me to insert the fuse holder without removing the parking unit bracket.


erWin indicates a procedure to remove and install the bracket for the parking unit, but it is a crap procedure because the plastics on the bracket tabs are of very, very, very poor quality. It is very easy to break the plastic tabs.
Image

Image
Note: At this point I want to emphasize that currently the manufacturing quality of plastics has notably worsened (6R 2013 vs G7.5 2019), the ones used in the 6R are of better quality.



To avoid breaking the plastic tabs, it is best to remove the BCM, press lightly on the plastic tabs, and pull down the parking unit bracket. Easy.
Image

Image


With the help of the pliers the new fuse holder is inserted little by little and kindly into the parking unit bracket. Easy.
Image
Note: I could have saved myself this explanation. 🤪
- Reference number of the parking unit bracket: 5Q0937503F (11€ approx)


Connections.

Once all the harnesses of this installation reach the TIUL coupling point, I proceed to connect the wires.

This is how I'm going to do it:

Code: Select all

LEVEL SENDER G76

- Blue wire to T73a/23
- Black wire to T73a/22
- Brown wire to T73c/57 ... (ground)


-----------------------------------------------

FCM J745

- CAN convenience 
Driver door ... 4 high green-orange , 5 low brown-orange
TIUL black ... 6 high green orange , 11 low brown-orange

- CAN extended (many devices here, slightly saturated :)))
TIUL black ... 12 high grey , 13 low brown-orange --> new splice-->T2 connector: H grey-black , L white-black
Connect to new T2 connector ... H black , L white-black

- CAN headlights
Direct connection 
grey-orange ... high
brown-orange ... low

- Positive +30
TIUL black ... '8' or 9 new red-black wires.

- Negative -31
brown ... ground point.


-----------------------------------------------

NEW FUSES (Wires: red 2.5mm, red 2.5mm -/> 0.5mm x2, white x2: 0.75mm )


- whites (+15 headlights, SC 36 and 37) ...From 123...to   7.5A x 2
Headlights white wires. Direct connection.

- red (+30) 2.5mm -/> 0.5mm x2 ...From 120...to   10A 
TIUL black ... '8' and 9 red-black.

- red (+30) 2.5mm ...From L128...to   *30A 
Any TIUL 16 slot connector , choose the most easy to work in the future. 


-----------------------------------------------

8IU LED HEADLIGHTS *Automatic headlights control. (cut T46b/2 and 39 wires with the same length :)))

LEFT MX1

- Feed (low beam). T73c/5 red wire. Direct connection (isolate original)
- Sig (High beam? - SCLs? - P/S/M - BLK - DRL). T46b/2 black-blue wire. Direct connection (isolate original)
- +15. white wire. Direct connection to fuse.
- CAN, direct connection to FCM.

RIGHT MX2

- Feed (low beam). T46b/1 red wire. Direct connection (isolate original)
- Sig (High beam? - SCLs? - P/S/M - BLK - DRL). T46b/39 black-yellow wire. Direct connection (isolate original)
- +15. white wire. Drect connection to fuse.
- CAN, direct connection to FCM.


-----------------------------------------------

CAMERA -A5-

- Can Extended
To new T2 ... grey-orange to grey-black , brown-orange to white-black.

- CAN ACC --> A5
ACC. 5 High white-orange , 6 low brown-orange.
TIUL brown. 9 High white-orange , 11 low brown-orange.

- +15 positive. 
TIUL black 15. green-black wire.

- -31 negative.
brown ... grown point.


---

- Dome lights buttons (58d). T6/3 blue connector --> T73c/62 grey... splice new black wire. (Y)
Image

It will take some time for a new update of this installation, I have yet to receive some parts that I requested, ... between the delays due to the pandemic, the Christmas holidays, the adverse weather conditions where I live and other PRO circumstances there will be delays.

Slow but safe. We endure. We resist! :lol:
User avatar
ciclo
Bling Bling Diamond Member
Posts: 6147
Joined: Sun Feb 24, 2013 10:20 am
Drives: 6R Rline/G7.5/Touareg Rline'19/T-Cr'20
Location: Earth ♥, Spain ☼
Contact:

Re: ciclo. Wife's Golf MK7.5 Ready2Go 1.0 TSI 6MT 200Nm/l 115HP

Post by ciclo »

5Q0937503F

Image

I find it very rare that this bracket has 9 dedicated places to hold the parking unit, 4 relay holders or fuse holders and another 4 for connectors or other devices and is finally held by a system that is based on two such weak tabs. In my humble opinion, a very elaborate bracket but with a weak clamping system.

I suppose it is because it is made of plastic and a new one does not imply a high cost, ... I can think of hundreds of ways to fasten it much better or repair it if necessary, however, I bought a new one. :|

Image


Finally 👉, inserting or removing the single relay holder or the 2-fuse holder is as it should be, a very easy task and will not require removing the bracket for the parking unit, so I recommend buying this type of holder/s for your retrofits.
Image

Image
:mrgreen:

---
Image
User avatar
ciclo
Bling Bling Diamond Member
Posts: 6147
Joined: Sun Feb 24, 2013 10:20 am
Drives: 6R Rline/G7.5/Touareg Rline'19/T-Cr'20
Location: Earth ♥, Spain ☼
Contact:

Re: ciclo. Wife's Golf MK7.5 Ready2Go 1.0 TSI 6MT 200Nm/l 115HP

Post by ciclo »

Heeelp! :lol: . Original wiring for HELIX sound system. CHW051419B

As some of you know, I installed the Helix sound system in my 6R:
- viewtopic.php?p=538499#p538499
- viewtopic.php?p=538553#p538553
- viewtopic.php?p=540220#p540220

Now I found this programmer on eBay:
Image
I bought it, because I want to test the Helix sound system on my wife's Golf 7.5.

:arrow: https://www.volkswagen-zubehoer.de/de/p ... ystem.html
Image

So I only need to install the wiring for the sound system in the Golf to be able to use the subwoofer and amplifier in both cars:
Image

CHW051419B

Someone would be so kind to help me find this wiring or provide it to me before I decide to make it myself.

Please contact me by private message if you want to make me an offer.

Thanks in advance.


---
Edit

Your help is no longer necessary, thanks, I have already bought all the parts (less than 50 euros) and I have all the info to make this wiring myself.
Post Reply