Page 5 of 8
Posted: Wed Dec 10, 2008 9:58 am
by Jeff GTi
am i the only one being picky here, but the gti vents are silver-ish in colour, not black
also, does it not look like it sticks ot a bit too far???????????
Posted: Wed Dec 10, 2008 11:51 am
by stanya
1/ GTi_Dan
2/ More-BHP
3/ dkny2789
4/ LeMeph
5/ SiDaBa
6/ OzGrant
7/shaneth
8/ bucko
9/ pip_polo
10/ whitegtipolo
11/ Jeff GTi
12/ flyfs6
13/ benny c
14/ j0n_GTI
15/ oliverpologti
16/ Rich_T
17/ chris 9n
18/stanya
that luks beta than i thought it would!
is it easy to get the cables ect. through the heatin pipe?
Posted: Wed Dec 10, 2008 1:11 pm
by Jeff GTi
though, im nearly certain it would be possible to fit just the vent and holder bit to the existing gti vent to prevent a poor colour match eh?
thus making it a perfect fit too?????
im still interested either way
Posted: Wed Dec 10, 2008 1:13 pm
by SiDaBa
Jeff GTi wrote:though, im nearly certain it would be possible to fit just the vent and holder bit to the existing gti vent to prevent a poor colour match eh?
thus making it a perfect fit too?????
im still interested either way
I was under the impression it was going to be just the vent bit to save on costs.
Posted: Wed Dec 10, 2008 1:44 pm
by Rich_T
Jeff i presumed it would be a matching vent for the GTi
Posted: Wed Dec 10, 2008 2:23 pm
by GTi_dan
Hi Jeff,
SWG are producting just the insert (see 85% finished prototype below) to fit in the existing 'silver-ish' GTI vent shell.
I'm told it would end up very expensive for SWG to produce the whole vent assembley.
Posted: Wed Dec 10, 2008 2:48 pm
by Jeff GTi
even better, sounds excellent then
Posted: Wed Dec 10, 2008 3:20 pm
by DUB-POLOW
and ad me please
Posted: Wed Dec 10, 2008 4:07 pm
by loud
1/ GTi_Dan
2/ More-BHP
3/ dkny2789
4/ LeMeph
5/ SiDaBa
6/ OzGrant
7/ shaneth
8/ bucko
9/ pip_polo
10/ whitegtipolo
11/ Jeff GTi
12/ flyfs6
13/ benny c
14/ j0n_GTI
15/ oliverpologti
16/ Rich_T
17/ chris 9n
18/ stanya
19/ dub-polow
20/ loud
Posted: Fri Dec 12, 2008 8:44 pm
by GTi_dan
Hi Guys,
Another little update....
(Extract from email)
The prototypes nearly finished I've designed it so it sits on 4 lugs placed on the ends of the slats, this enables it to locate in the correct position in the housing so it should be a simple case of taking the original vent apart removing the slats and slotting in the new insert.
All being well I might be able to do the tooling towards the end of next week, unfortunately due to Christmas being so close delivery before is looking unlikely.
1/ GTi_Dan
2/ More-BHP
3/ dkny2789
4/ LeMeph
5/ SiDaBa
6/ OzGrant
7/ shaneth
8/ bucko
9/ pip_polo
10/ whitegtipolo
11/ Jeff GTi
12/ flyfs6
13/ benny c
14/ j0n_GTI
15/ oliverpologti
16/ Rich_T
17/ chris 9n
18/ stanya
19/ dub-polow
20/ loud
Posted: Fri Dec 12, 2008 10:09 pm
by whitegtipolo
Posted: Fri Dec 12, 2008 11:39 pm
by Jeff GTi
excellent news
Posted: Sat Dec 13, 2008 1:16 am
by titan619
1/ GTi_Dan
2/ More-BHP
3/ dkny2789
4/ LeMeph
5/ SiDaBa
6/ OzGrant
7/ shaneth
8/ bucko
9/ pip_polo
10/ whitegtipolo
11/ Jeff GTi
12/ flyfs6
13/ benny c
14/ j0n_GTI
15/ oliverpologti
16/ Rich_T
17/ chris 9n
18/ stanya
19/ dub-polow
20/ loud
21/ titan619
Posted: Mon Dec 15, 2008 6:20 pm
by chris 9n
is it a dash out job or can it be fitted with it in
MY DASH IS ALL OUT AT THE MO .JUST WONDERED IF WHEN I PUT IT BACK WILL I HAVE TO TAKE IT OUT AGAIN
thanks
chris
Posted: Mon Dec 15, 2008 6:29 pm
by GTi_dan
Already thought of that, so done some digging....
1st and 4th diagrams are relevant i think?
