UK-POLOS.NET - THE VW Polo Forum

Does the HBA work well after this change?

HBA has always worked well, I’ve not tried it since the MKE addition, but I don’t see why not?

I tried with VCP and converted file. I have fault when loading via VCP, but MKE works.
Moment ago I noticed new issue: when I turn on HBA I can't disable it :O
Here is video: https://photos.google.com/share/AF1QipP ... BMajJsRS13

CNK wrote: Sat Jun 15, 2019 10:20 pm I tried with VCP and converted file. I have fault when loading via VCP, but MKE works.

What is the fault?

Post here the converted file that you have loaded. Between []

CNK wrote: Sat Jun 15, 2019 10:20 pm Moment ago I noticed new issue: when I turn on HBA I can't disable it :O
Here is video: https://photos.google.com/share/AF1QipP ... BMajJsRS13

Your HBA system works perfectly according to the video.

Check this video to find out who or what does not work correctly.

Do exactly the same as in the video.

Ok, sorry for the confusion. I think I was too tired

So it's okay, during the day we switched HBA/no HBA because we use DRL. At night we switched HBA/high beams, because we have low beams turned on

Converted file: https://pastebin.com/Xg02rYM6

Fault in VCP:

Error writing memory : 49 Operation Write_data_to_F1A1 31 Request out of range.

(i use the original VCP)

I can send you the file I used for VCP if you like? I had a quick look at yours and without comparing it looks ok.

I wrote with firegrafik, he did a test on his old BCM and had the same fault, but noticed it works despite the error in VCP.
Didn't you have this error?

CNK wrote:I wrote with firegrafik, he did a test on his old BCM and had the same fault, but noticed it works despite the error in VCP.
Didn't you have this error?

No, mine said writing ok, do you get errors (dtc) reading the module?

I have only high beam headlamp bulb faults (Break / short to + Lamp OFF), left and right (I think I have this after HBA install, all works but can't fix these faults).

Adam87 wrote: Sun Jun 16, 2019 10:24 am

CNK wrote:I wrote with firegrafik, he did a test on his old BCM and had the same fault, but noticed it works despite the error in VCP.
Didn't you have this error?

No, mine said writing ok, do you get errors (dtc) reading the module?

Question (only):

Adam, did you check the EraseFullMemory box when loading the data set?



---
Remember that the GW coding in Byte2 is not 05 HEX, it is 04 HEX.

No because it’s not a full memory flash, just a section. Or a t least that is my thoughts. It worked anyway haha.

Did you Fernando?

Ok.

I did it with ODIS-E (recommended, I hope you have it soon).
Everything perfect with a single try.

Superhappy with ODIS-E!

Do you use ODIS-e with VAS 5054 cable?

I had no issue using VCP but just a little more time figuring out how to convert file from Odis to VCP

ciclo wrote: [emoji1787]

Be right back once I’ve watched all 7 HOURS....! [emoji23] btw, how long did it take to learn to play all them horns???[emoji2957]

Adam87 wrote: Sun Jun 16, 2019 7:05 pm Do you use ODIS-e with VAS 5054 cable?

Yes, ODIS-E 9.0.4 with VAS5054, under W7, I connect it via Bluetooth, without cable.
I have used it twice, once to flash/update my second ECU viewtopic.php?f=56&t=58703&start=4695#p556178 , the other to load the MKE data set.
Everything perfect, without any kind of deficiency ...

ODIS Engineering 9.0.4



---
I'm going to test how the Konis Hupen sounds with my Helix sound system.

Hi Adam,

I’m trying to contact you regarding the wiring for the retrofit or AC. Do you still have any information?


Cheers