1.8 8V
Posted: Mon Oct 30, 2006 5:54 pm
will this fit it's out of the mk2 golf.if so were can i get it done.plz help ppl say it wont but sum say might.ppppppppppplllllllllllllllllllzzzzzzzzzzzz HELP!
UK-POLOS.NET - THE VW Polo Forum
Probably the Worlds greatest Polo resource
https://uk-polos.net/
1.8 8V
Page 1 of 2
Posted: Mon Oct 30, 2006 6:28 pm
If your going for an engine conversion, wouldnt it be more worth while going for a 20V 1.8T or something? Just a thought.
Posted: Mon Oct 30, 2006 9:10 pm
1.8t and vr6 have both been done. can't see why you'd put an 8v 1.8 in there instead of a more modern engine?
Posted: Mon Oct 30, 2006 9:58 pm
I can:
1) cheap
2) can do it yourself with less mechanical know-how
3) ecu and wiring can be ditched easier - if you carb it instead
4) easier to source cheap parts!
5) someone might have one free for you!
and so on - in fact if you got a written off 8v GTI there's a lot of parts that just might fit.....
but i don't know which! all I know is a 20v lump would cost about 4k to put in
1) cheap
2) can do it yourself with less mechanical know-how
3) ecu and wiring can be ditched easier - if you carb it instead
4) easier to source cheap parts!
5) someone might have one free for you!
and so on - in fact if you got a written off 8v GTI there's a lot of parts that just might fit.....
but i don't know which! all I know is a 20v lump would cost about 4k to put in
Posted: Mon Oct 30, 2006 10:54 pm
true, true.
Posted: Mon Oct 30, 2006 11:06 pm
The guy is obviously considering the 1.8 8v as he is on a relative budget! I'm pretty sure he would go for the 20vT if it was thaty easy and cheap.mc_iver_9n wrote:If your going for an engine conversion, wouldnt it be more worth while going for a 20V 1.8T or something? Just a thought.
I personally think you should go for a more modern engine tho, 1.4 16c 100bhp engine or something? Its meant to be really quick. Or say the GTI engine from the 6n2? Not very expensive.
I dont really know the power of the older GTI engines etc, but i would assume they'de be quite nippy and light, but imho it would prob deppreciate the value of the car due to the engines age and more than likely high mileage.
just my 2p's worth tho.
Posted: Mon Oct 30, 2006 11:47 pm
If you've got the engine handy then bang it in, not really sure what you'd need to do it but i bet good money it would fit as 1.8t's 2.0l 16v's and VR6's have all gone in.
Getting the 1.8 8v engine in would probably be quite easy due its smallish bulk and you'd end up with a very light and torquey car
Getting the 1.8 8v engine in would probably be quite easy due its smallish bulk and you'd end up with a very light and torquey car
Posted: Tue Oct 31, 2006 11:47 am
Yer thats TrueDee-vub wrote:The guy is obviously considering the 1.8 8v as he is on a relative budget! I'm pretty sure he would go for the 20vT if it was thaty easy and cheap.mc_iver_9n wrote:If your going for an engine conversion, wouldnt it be more worth while going for a 20V 1.8T or something? Just a thought.
Posted: Tue Oct 31, 2006 1:17 pm
It will physically fit, but thats about it. You'd have to adapt the mounts from both a polo and a golf together. The mounts on a mk2 golf are completely differant. They are nice engines for acceleration but top end isnt much. You may need to cut the chassis legs to allow fitment, also i dont know what box/driveshafts you could use. The Polo engines are based around the 1.1/1.3 mk1 engines where they have a short block. The mk2's have a long block. It may be worth looking at a 1.3 mk2 and comparing the mounts with a gti. That way you could see what was needed.
I'd go for a 6n2 gti engine. You could get one for a few hundred and it'd go straight in.
I'd go for a 6n2 gti engine. You could get one for a few hundred and it'd go straight in.
Posted: Tue Oct 31, 2006 5:54 pm
thank you.your spot on there im abit spent.whant the 8v coz its is better down low and better in town.the polo gti sound's good there 125 bhp (think so)what can you do to them and will gti discs fit? thanks for the help
Posted: Tue Oct 31, 2006 7:10 pm
i imagine all the bits of a 6n2 will fit a 6n without too much bother to be honest. the more 6n2 parts you can pilfer the better!
Posted: Tue Oct 31, 2006 8:11 pm
Might even be easier if you fit a 6n2 dash while you're there? Now that would be sweet 
Posted: Tue Oct 31, 2006 10:25 pm
not havin a go mate if it sounded like that, its just that the 1.8T is most of our dream engines and the price is prety much which stops 99% of people doing it to be honest!mc_iver_9n wrote:Yer thats TrueDee-vub wrote:The guy is obviously considering the 1.8 8v as he is on a relative budget! I'm pretty sure he would go for the 20vT if it was thaty easy and cheap.mc_iver_9n wrote:If your going for an engine conversion, wouldnt it be more worth while going for a 20V 1.8T or something? Just a thought.
But yeh Gti brakes will go on easy! A 6n2 dash conversion would be sweet, but in al fairness, if you would want all this from a 6n2, just get a 6n2
Posted: Tue Oct 31, 2006 11:26 pm
Yer i just thought engine conversion in a polo - 1.8T as u doDee-vub wrote:not havin a go mate if it sounded like that, its just that the 1.8T is most of our dream engines and the price is prety much which stops 99% of people doing it to be honest!mc_iver_9n wrote:Yer thats TrueDee-vub wrote: The guy is obviously considering the 1.8 8v as he is on a relative budget! I'm pretty sure he would go for the 20vT if it was thaty easy and cheap.
But yeh Gti brakes will go on easy! A 6n2 dash conversion would be sweet, but in al fairness, if you would want all this from a 6n2, just get a 6n2
wasnt thinking about budget lolPosted: Tue Oct 31, 2006 11:28 pm
Erm
The tall block 1.8 engine won't fit?
The tall block 1.8 engine won't fit?