Page 1 of 1
Choosing the Right Wheels...Can any1 help???
Posted: Sun Dec 10, 2006 4:53 pm
by keenan27
New to the forum and i am currently in the process of buying new 17"
wheels for my polo 9n.
The wheels that i am planning on buyin are:
7x17", 205/40/17 , 5x100 et42
Can any1 tell me if this wheel is the right size and whether it will rub the arch.
Cheers
Posted: Mon Dec 11, 2006 1:58 pm
by SiDaBa
Yep sounds fine to me.
Believe that might be the same size and offset as mine.
As far as I'm aware mine haven't rubbed and I'm lowere about 60mm
Posted: Mon Dec 11, 2006 5:29 pm
by mc_iver_9n
Same as me. Although I think my offset could be lower, not too sure tho. Tyre size and everything is fine. You willl need lowered at least 30mm for them to sit nicely in the arch. Although the lower the better i say (within reason). Just out of interest, What wheels are you getting?
Posted: Mon Dec 11, 2006 6:49 pm
by jmv
mine are the same off set but with 205/45/17 tyres. because my skirts are low though. there must be a 2'' gap around the arch on the rear!!
Posted: Mon Dec 11, 2006 7:37 pm
by keenan27
Thanks very much. just what i wanted to hear, wasnt to sure as i am no genius as it comes to cars or the mechanics behind it.
The wheels i am getting are Lenso Elsegence
http://www.rochfordtyres.co.uk/product. ... strSize=17"
If you see anything obvious about them not fitting, please let me know
Thanks very much
Posted: Mon Dec 11, 2006 8:59 pm
by AKs_SlickPolo
Isn't the offset meant to be ET38 or lower to fit on Polo's
as i believe thats what the standard wheels are. As If you have it too high it may rub on the shocks unless coilovers are used
Posted: Mon Dec 11, 2006 9:55 pm
by SiDaBa
AKs_SlickPolo wrote:Isn't the offset meant to be ET38 or lower to fit on Polo's
as i believe thats what the standard wheels are. As If you have it too high it may rub on the shocks unless coilovers are used
higher the offset the further the wheels are from the hub and then surely the further away from the Shocks they are
And looking through my e-mails my wheels are ET35
Posted: Mon Dec 11, 2006 10:01 pm
by carmadaaron
SiDaBa wrote:AKs_SlickPolo wrote:Isn't the offset meant to be ET38 or lower to fit on Polo's
as i believe thats what the standard wheels are. As If you have it too high it may rub on the shocks unless coilovers are used
higher the offset the further the wheels are from the hub and then surely the further away from the Shocks they are
And looking through my e-mails my wheels are ET35
better to stick with offsets ~35
42 may cause probelms when lowered.
Posted: Mon Dec 11, 2006 10:17 pm
by AKs_SlickPolo
SiDaBa wrote:AKs_SlickPolo wrote:Isn't the offset meant to be ET38 or lower to fit on Polo's
as i believe thats what the standard wheels are. As If you have it too high it may rub on the shocks unless coilovers are used
higher the offset the further the wheels are from the hub and then surely the further away from the Shocks they are
And looking through my e-mails my wheels are ET35
What I meant was, As the offset gets lower (i.e from ET42 to ET35) the wheels are further from the hub so they are not close to the shocks
.
But yeah my old wheels were ET35 and I say too thats a good offset.
Though anything between ET25-ET38 would be fine.
Rears can even run ET15s without archwork if not excessively lowered
.
Posted: Tue Dec 12, 2006 5:42 pm
by jmv
so a lower offset number mean the wheels will stick further out of the arch???
Posted: Tue Dec 12, 2006 6:17 pm
by polo power
wheels look pretty good, quite like them wouldnt look right on my 6n2 tho.
Posted: Tue Dec 12, 2006 10:01 pm
by carmadaaron
jmv wrote:so a lower offset number mean the wheels will stick further out of the arch???
yes