My CW Pgti.
Posted: Thu Nov 08, 2012 7:21 am
Sup guys
Thought i'd finally make a thread on here . Enjoy
all comments welcome.
engine mods:
REVO Stage 2
Cupra FMIC
Forge TIP
Forge 008 DV
ITG Intake
4 bar FPR
Flowtech 76mm DP
Powerflow 63 SS exhaust.
exterior mods as follows
lamin-x on head and fog lights
6000k xenon headlights
4000k fog lights
honeycomb lower grills
bonnet bra
seat cupra lip
H&R 35mm springs
Took her down to my hometown this weekend
snapped a couple pics last night cos i was bored :crazy:
Took the bonnet bra off to have the car washed at work (they do an amazing job, and for 10 bucks extra he Meguiars the car
) , ended as a fail because i had to leave before he could wash it 
some random pics
Dyno'd again at FRnR, car was a bit warm, but still very happy with the figures
I drove to my hometown again for the long weekend, and met up with some homies for a Breakfast run.
we then decided to hit up the seat bullrun and do a mini shoot
Then we took a drive out to in the town and found a pretty cool place to snap some more cool photos .
Enjoy! let me know what you think!
So i Fitted a full Exhaust at powerflow , its a 63mm from the downpipe back with 1 box :thumb: , Absolutely Loving it! Car revs up like an animal throughout the gears.
Pics for Clicks!
Arriving on the scene..
Car on the ramp and the old exhaust being rermoved.
The old exhaust
The two new tips i chose, something a little bigger than standard. Fills the rear valance quite nicely.
Flowtech Downpipe
Pipe now in, Box being fitted
Finished Product. Classy :afro: hehe
Underside shot
Went through to FR&R for one of their Dyno Nights.
Decided to Put the Polo on the rollers
And was extremely happy with the figures! :cheers: :cheers:
so i was searching for a new set of wheels for the polo, initially found a set which turned out to be 5x112, so i went through to the wheel shop to find out about drilling them to 5x100, whilst there i saw a set of these OZ futura's on display. I asked if i can have the wheel test fitted to see how it would look.
after which, i asked what sizes he had available, he told me he was out of stock of 5x100 17", but if i wanted a set he would fetch them for me the same day, naturally i said yes please!, and within an hour he was back with 4 of the best! narrows and wides as well! 7.5j and 8.5j
the tyres were then fitted in no time! 205/40/R17 all round.....
and here it is on the car.
Those lips
The following day, it was time to hit FR&R Tuning for Dyno War!!!
FR&R's finest ..... Easily some of the Hottest Dubs around
On the Rollers!
The result of the runs...
1st place in the 1.8T and 1.4t class! :cheers: :cheers:
This week will be a big one!, the coils arrive today! hopefully fitment will happen tomorrow
Thought i'd finally make a thread on here . Enjoy
all comments welcome.
engine mods:
REVO Stage 2
Cupra FMIC
Forge TIP
Forge 008 DV
ITG Intake
4 bar FPR
Flowtech 76mm DP
Powerflow 63 SS exhaust.
exterior mods as follows
lamin-x on head and fog lights
6000k xenon headlights
4000k fog lights
honeycomb lower grills
bonnet bra
seat cupra lip
H&R 35mm springs
Took her down to my hometown this weekend
snapped a couple pics last night cos i was bored :crazy:
Took the bonnet bra off to have the car washed at work (they do an amazing job, and for 10 bucks extra he Meguiars the car
) , ended as a fail because i had to leave before he could wash it some random pics
Dyno'd again at FRnR, car was a bit warm, but still very happy with the figures
I drove to my hometown again for the long weekend, and met up with some homies for a Breakfast run.
we then decided to hit up the seat bullrun and do a mini shoot
Then we took a drive out to in the town and found a pretty cool place to snap some more cool photos .
Enjoy! let me know what you think!
So i Fitted a full Exhaust at powerflow , its a 63mm from the downpipe back with 1 box :thumb: , Absolutely Loving it! Car revs up like an animal throughout the gears.
Pics for Clicks!
Arriving on the scene..
Car on the ramp and the old exhaust being rermoved.
The old exhaust
The two new tips i chose, something a little bigger than standard. Fills the rear valance quite nicely.
Flowtech Downpipe
Pipe now in, Box being fitted
Finished Product. Classy :afro: hehe
Underside shot
Went through to FR&R for one of their Dyno Nights.
Decided to Put the Polo on the rollers
And was extremely happy with the figures!
:cheers: :cheers: so i was searching for a new set of wheels for the polo, initially found a set which turned out to be 5x112, so i went through to the wheel shop to find out about drilling them to 5x100, whilst there i saw a set of these OZ futura's on display. I asked if i can have the wheel test fitted to see how it would look.
after which, i asked what sizes he had available, he told me he was out of stock of 5x100 17", but if i wanted a set he would fetch them for me the same day, naturally i said yes please!, and within an hour he was back with 4 of the best! narrows and wides as well! 7.5j and 8.5j
the tyres were then fitted in no time! 205/40/R17 all round.....
and here it is on the car.
Those lips
The following day, it was time to hit FR&R Tuning for Dyno War!!!
FR&R's finest ..... Easily some of the Hottest Dubs around
On the Rollers!
The result of the runs...
1st place in the 1.8T and 1.4t class! :cheers: :cheers:
This week will be a big one!, the coils arrive today! hopefully fitment will happen tomorrow
