UK-POLOS.NET - THE VW Polo Forum

On the older clusters sold in India, there's no CC led. So no notification comes up.

Fernando, I cannot thank you enough for the help you have rendered so far especially the current flow diagrams of various things that I have asked you. Installed cruise control yesterday and the new steering wheel and everything worked flawlessly! It was such an awesome experience doing it. As for t...

1. That's the coolant temp. gauge if you are referring to this one:



90'C is the optimum operating temperature of the coolant - no issues there.

2. Do check the fuse. Being a brand new car, I wouldn't suspect a bad harness or component, but do check the fuse.

Grabbing these. Thanks a lot Fernando!

Mart!n-GTI-DK wrote:It will not read correctly in a TDI and you will also lose the engine heater light.

Will not read what correctly? Please be specific.

The glow plug light can be substituted for the EPC light using a bit of EEPROM coding so that is not an issue.

iichel, how hard was it to take off the stock mirror clamp which was glued to the windshield? What chemical/solution did you use to take it off the windshield?

My question then: Does a left spoke MFSW airbag work with a GTI steering wheel? That is, will the airbag from this steering below... http://i.imgur.com/5OGSQYw.jpg ...fit this one: http://i.imgur.com/ujiyi9m.jpg I think it does. One guy has managed to use the one from his stock MFSW (with just the ...

The glow plug light is being substituted by the EPC light in function. De paticulate filter warning is now on the pixel screen. iichel, I don't get the EPC light on my cluster. Is there a way to get this light activated? Can VCDS be of any use here? I only get these lights when I turn the key to AC...

The GTI tacho doesn't have issues if it is used on a diesel car. I have a GTI tacho on my 1.6 TDI. Tacho works just like the stock one but the downside is the lack of the glowplug warning light on the GTI cluster. I am guessing the LED is not soldered on the board. For swapping the cluster, the immo...

Will figure this out in one way or the other. Ciclo, do you have the wiring diagram for the dashboard illumination controller? Here in India, VW does not provide one in the headlamp range control knob. It’s like this: http://i.imgur.com/3WL8qbL.png Whereas with the illumination control, it should be...

Thank you ciclo. I think there might be a dummy hole with a grommet on the co-driver side as well. Let me check. ciclo, I can confirm that there is a dummy hole covered by a rubber grommet on the co-driver side. Will try to route the wire through the hood release grommet since that will be closest ...

ciclo wrote:T32/17

You're right Gannu.



As you can see sensors share a common earth. T32/20

Thanks a bunch brother! Much appreciated!

Ok, thanks to you for your excellents DIY in your forum (team-bhp). :wink: Thanks a lot to you too for this informative thread ciclo! The glovebox light mod was inspired by the one you did. :) Unfortunately for us, we do not have many competent garages here so the only way out is to refer to the VW...

Thank you ciclo. I think there might be a dummy hole with a grommet on the co-driver side as well. Let me check. Or will use a pointed object like a needle and insert the cable through the hood release grommet from the inside to the engine bay side. Will keep you posted. Thank you once again! I am p...

Ciclo, need some help. What is the easiest way for routing a thin wire through the firewall/bulkhead? I saw the rubber grommet for the hood release cable but it is located a bit inside and may have to remove the wipers and the plastic trim to gain access. Is there another point?

Thanks in advance!