haha i need dish!! as they are custom 3 piece the barrels are only 6" so the rears will have 6" of purrrre dish
they need to make the OEM rears look feeble and skinny!
Cupra sold, Progress thread - Z3M - Custom 3 piece BBS
-
- Bling Bling Diamond Member
- Posts: 2149
- Joined: Mon Oct 23, 2006 12:24 pm
- Location: Bournemouth Drives: 6n2 TDi
- Tim_GTi
- Post Whore
- Posts: 12289
- Joined: Mon Jun 25, 2007 6:31 pm
- Location: Newport, South Wales
- Contact:
Re: Cupra sold, Progress thread - Z3M
What kind of tyre would you require for them then?!
-
- Bling Bling Diamond Member
- Posts: 2149
- Joined: Mon Oct 23, 2006 12:24 pm
- Location: Bournemouth Drives: 6n2 TDi
Re: Cupra sold, Progress thread - Z3M
No idea lol! the standard rears are 9" which run 245/40/17. I plan on a bit of stretch but not too much
Re: Cupra sold, Progress thread - Z3M
Just had a little read and 12J rears goin be insane .. cant wait to see them on the car
-
- Bling Bling Diamond Member
- Posts: 2149
- Joined: Mon Oct 23, 2006 12:24 pm
- Location: Bournemouth Drives: 6n2 TDi
Re: Cupra sold, Progress thread - Z3M
Cheers rhys, i've got a fair bit of work to do to them before they are fitted
Over the period of a few weekends I've been giving the car a real good going over inside and out including engine bay/boot etc..
Here's a few pics
My rubber aerial grommet, looks so much better! simple things !
Also a teaser pic before I polish the wheels up :
Any guesses?
Over the period of a few weekends I've been giving the car a real good going over inside and out including engine bay/boot etc..
Here's a few pics
My rubber aerial grommet, looks so much better! simple things !
Also a teaser pic before I polish the wheels up :
Any guesses?
- Tim_GTi
- Post Whore
- Posts: 12289
- Joined: Mon Jun 25, 2007 6:31 pm
- Location: Newport, South Wales
- Contact:
Re: Cupra sold, Progress thread - Z3M
Looking good.
LMs?
LMs?
-
- Bling Bling Diamond Member
- Posts: 2149
- Joined: Mon Oct 23, 2006 12:24 pm
- Location: Bournemouth Drives: 6n2 TDi
Re: Cupra sold, Progress thread - Z3M
Bingo well done Tim
Here's one after a bit of polishing:
Custom 3 piece 19x8.5" LM's ET9&13 with Image/Schmidt 2.5" Lips & 6" Barrels
The current lips have too many holes (because they are originally for Image/Schmidt rims) but the new ones will be drilled with the right number, if I decide to make use of the current lips on the front i'll use the inserts from fake LM's, I doubt they will fit because of the low offset though.
If anyone has any standard 19" LM's and wants more dish & a low offset for the rear drop me a PM as i'm after two standard barrels to get a high offset up front.
Already on the shopping list: 5.5" lips for the rear to make 11.5's and new bolts all round
Here's one after a bit of polishing:
Custom 3 piece 19x8.5" LM's ET9&13 with Image/Schmidt 2.5" Lips & 6" Barrels
The current lips have too many holes (because they are originally for Image/Schmidt rims) but the new ones will be drilled with the right number, if I decide to make use of the current lips on the front i'll use the inserts from fake LM's, I doubt they will fit because of the low offset though.
If anyone has any standard 19" LM's and wants more dish & a low offset for the rear drop me a PM as i'm after two standard barrels to get a high offset up front.
Already on the shopping list: 5.5" lips for the rear to make 11.5's and new bolts all round