UK-POLOS.NET - THE VW Polo Forum

1) It depends from your installation but sometimes the linbus wire is located in the door loom, so you could easily access it there. If you don't have the linbus wire there then you must get it from the BCM directly. Most likely there is no wire yet in pin T73b/17. You might even have to put in a di...

You did not save original ABS coding? Or made a full auto scan anywhere before in the past?
I see you used ODIS in the past, maybe you have stored a full log of it somewhere? There you can find your original ABS coding also.


Goodluck,
H2Deetoo

When you finish a bcm max retrofit in that UP we'll meet

Trust me, I'm a large fellow and my hand, fingers, neck and back hurt like h*ll. But once you start this adventure (started this BCM swap simply for MFSW retrofit) you simply cannot stop ;-) And I did it one part at a time, first just the BCM, then some power signals, then low beam, etc.etc. so I sp...

Thanks for the links. I will review them and update my label file if apropriate.


Thanks again for your time and effort!

H2Deetoo

Ciclo, your help is greatly appreciated, ever since the beginning of this project! I did set bit 1 of byte 27 now and interiour lights *are* working now ! And no fault codes in bcm: Friday,20,November,2020,18:48:54:00008 VCDS Version: Release 18.9.1 Running on Windows 7 x86 www.Ross-Tech.com Address...

I am sorry I made a mistake in copying, my apologies. But I need to change 1 bit because I have an automatic gear and not a manual gear, so byte 27 needs to be 40h and not 42h. After writing the correct coding you specified (byte 18 to 60h instead of 40h which I forgot) the main beam *is* working! G...

Hi, I tried the new coding and the situation remains the same: No interior lights, no permanent high beam (stalk forward). Also no faults (even after driving for a minute): Address 09: Cent. Elect. Labels: User\1S0-937-090-F.lbl Control Module Part Number: 1S0 937 090 F HW: 1S0 937 090 Component and...

If the current license plate installation will result in some error I will put a new wire directly to T73b/7 to sort it

Fresh auto scan: Friday,20,November,2020,16:00:17:00008 VCDS -- Windows Based VAG/VAS Emulator Running on Windows 7 x86 VCDS Version: 18.9.1.0 Data version: 20190114 DS296.0 www.Ross-Tech.com VIN: WVWZZZAAZED094213 License Plate: Mileage: 111560km-69320mi Repair Order: ------------------------------...

Hi, - DRLs under BCM control installed :?: YES - Interior lights dimmer installed :?: NO. I don't have a dimmer and when we discussed the loom I decided to not use an external dimmer. - LED license plate lights installed :?: No LED but normal lamp (I think). I did not connect it separately to BCM be...

Today I put in the auto-lights loom with red connector and 10pin headlight switch. Most lights work (fog front, fog rear, DRL, parking, dipped beam) but I have some problems: - main beam works only when flashing (pulling stalk towards me). It does not work when push stalk away. I see only ~1.5v on T...

Thanks for the explanation iichel!


Rgs H2Deetoo

Hi guys, Today I was able to rewire my DRLs so that they are under BCM control. Last week I already replaced the orig wire from T73b/11 with a new 1.5mm2 wire to free fuse SC50 (20A) which I wired to J33 with bridge to get 12v 30a, for my fog lights and as preparation for the DRLs. Here is what I di...

I just checked a Polo lowline cluster, it does have the icon and led soldered in place. Then I checked a Beetle 5C5 cluster (which is same hardware as the UP MFA+ cluster) and it doesn't have this icon. The layout could be different so I will check my actual UP cluster (later). I will simply try and...