It is not possible, I just checked.Franciswat wrote: ↑Tue Oct 03, 2017 5:36 pm Maybe I have to write on search box the pin number directly?
Franciswat's Polo 6R 1.6 Bifuel
- ciclo
- Bling Bling Diamond Member
- Posts: 7843
- Joined: Sun Feb 24, 2013 10:20 am
- Drives: 6R'13/G7.5'19
- Location: Earth ♥, sPAIN, Magiclands (Mordor).
- Contact:
Re: My polo 6r bifuel
- Franciswat
- Silver Member
- Posts: 267
- Joined: Thu Sep 21, 2017 9:39 am
- Drives: 6R 1.6 Bifuel
- Location: Italy
Re: My polo 6r bifuel
Ok after some searches I found wires sized.
Looking at the wiring diagram t6/3 of dimmer should go to t73b/1 so I suppose elsa refers to a 7H0 bcm instead of a 7E0.
car selected was polo 1.6 bmt highl 66 - 6r142v.
On the contrary I sould see t73b/4 instead of t73b/1 in the wiring diagram, shouldnt I?
I ask just becouse I saw t73b/4 and t73b/1 have different terminals so I want to be sure about wiring!
Thank you
PS I changed my mind and decided to install a 7E0.
Looking at the wiring diagram t6/3 of dimmer should go to t73b/1 so I suppose elsa refers to a 7H0 bcm instead of a 7E0.
car selected was polo 1.6 bmt highl 66 - 6r142v.
On the contrary I sould see t73b/4 instead of t73b/1 in the wiring diagram, shouldnt I?
I ask just becouse I saw t73b/4 and t73b/1 have different terminals so I want to be sure about wiring!
Thank you
PS I changed my mind and decided to install a 7E0.
- ciclo
- Bling Bling Diamond Member
- Posts: 7843
- Joined: Sun Feb 24, 2013 10:20 am
- Drives: 6R'13/G7.5'19
- Location: Earth ♥, sPAIN, Magiclands (Mordor).
- Contact:
Re: My polo 6r bifuel
Franciswat wrote: ↑Wed Oct 04, 2017 12:23 am
t73b/4
PS I changed my mind and decided to install a 7E0.
- Franciswat
- Silver Member
- Posts: 267
- Joined: Thu Sep 21, 2017 9:39 am
- Drives: 6R 1.6 Bifuel
- Location: Italy
Re: My polo 6r bifuel
Hi guys, I finally started working on wirings!
I got this crimper but for some reasons I am not able to use on terminals.
I got this crimper but for some reasons I am not able to use on terminals.
- ciclo
- Bling Bling Diamond Member
- Posts: 7843
- Joined: Sun Feb 24, 2013 10:20 am
- Drives: 6R'13/G7.5'19
- Location: Earth ♥, sPAIN, Magiclands (Mordor).
- Contact:
Re: My polo 6r bifuel
That tool is FOR INSULATED TERMINALS, it is clearly written on the label attached to it.
- Franciswat
- Silver Member
- Posts: 267
- Joined: Thu Sep 21, 2017 9:39 am
- Drives: 6R 1.6 Bifuel
- Location: Italy
Re: My polo 6r bifuel
Omg you are damn right!!!
I'll check for right crimper. Thank you mate!
I'll check for right crimper. Thank you mate!
- Franciswat
- Silver Member
- Posts: 267
- Joined: Thu Sep 21, 2017 9:39 am
- Drives: 6R 1.6 Bifuel
- Location: Italy
Re: My polo 6r bifuel
Hi i completed the bcm installation. Ive some problems because car does not recognise keyfog. I found procedure but It did not work. Can you explain It? Thank you!
- iichel
- Bling Bling Diamond Member
- Posts: 6405
- Joined: Fri Nov 14, 2014 2:14 pm
- Drives: Polo 6R 2.0 TDI, Passat B8 2.0 TSI
- Location: http://mypassat.nl/
-
- Gold Member
- Posts: 859
- Joined: Wed Apr 02, 2014 4:01 pm
- Drives: 1.2TSI 105HP DSG7
- Location: Malaysia
Re: My polo 6r bifuel
Hi Franciswat! nice mod! i thot i was looking at ciclo’s photos!! Cool.
btw. one interesting thing i found:
did you retrofit just the button set for this steering wheel? or it comes from factory like this?
ive friends who want to install the button set like below to the original steering with only left side button. Not sure its going to fit or not and how can i install the paddle shifter as well.
Sent from my iPhone using Tapatalk
btw. one interesting thing i found:
did you retrofit just the button set for this steering wheel? or it comes from factory like this?
ive friends who want to install the button set like below to the original steering with only left side button. Not sure its going to fit or not and how can i install the paddle shifter as well.
Sent from my iPhone using Tapatalk
- Franciswat
- Silver Member
- Posts: 267
- Joined: Thu Sep 21, 2017 9:39 am
- Drives: 6R 1.6 Bifuel
- Location: Italy
Re: My polo 6r bifuel
Guys i do not know What happened but the right headlight is always on (even with car Locked) and left headlight does no longer switch on.
- ciclo
- Bling Bling Diamond Member
- Posts: 7843
- Joined: Sun Feb 24, 2013 10:20 am
- Drives: 6R'13/G7.5'19
- Location: Earth ♥, sPAIN, Magiclands (Mordor).
- Contact:
Re: My polo 6r bifuel
Autoscan (whenever a new problem arises). The installation you have made depends largely on the coding.
I wonder why it is so hard to understand this.
I wonder why it is so hard to understand this.
- Franciswat
- Silver Member
- Posts: 267
- Joined: Thu Sep 21, 2017 9:39 am
- Drives: 6R 1.6 Bifuel
- Location: Italy
Re: My polo 6r bifuel
You are right mate, I'll provide you more details:
I have a stupid question about wirings: every fuse has 2 pins with unique number, when I have to replace original 34b, 39b and 59b wires with new one which pin I have to replace?
I have already copied coding from 09-Central Electronics module and 19-CAN Gateway and restored original installation list.
These are some problems occurred:
- Instrument panel and engine switch on but no longer off (neither removing key)
- Headligts do not work properly
- Light dimmer no longer works
- Impossible to set up remote controllers because channel's value doesn't change (image attached)
Code: Select all
VCDS Version: Release 15.7.1 Running on Windows XP x86
Data version: 20150904
www.Ross-Tech.com
Thursday,02,November,2017,00:52:50:05031
Chassis Type: 6R (7E0)
Scan: 01 03 08 09 10 15 17 19 25 44 56
VIN: WVWZZZ6Rxxxx Mileage: 63360km-39370miles
01-Engine -- Status: OK 0000
03-ABS Brakes -- Status: Malfunction 0010
04-Steering Angle -- Status: OK 0000
08-Auto HVAC -- Status: OK 0000
09-Cent. Elect. -- Status: Malfunction 0010
10-Park/Steer Assist -- Status: OK 0000
15-Airbags -- Status: OK 0000
17-Instruments -- Status: OK 0000
19-CAN Gateway -- Status: Malfunction 0010
25-Immobilizer -- Status: OK 0000
44-Steering Assist -- Status: Malfunction 0010
56-Radio -- Status: Malfunction 0010
-------------------------------------------------------------------------------
Address 01: Engine
Cannot be reached
-------------------------------------------------------------------------------
Address 03: ABS Brakes (J104) Labels: 6R0-907-37x-ESP82.clb
Part No SW: 6R0 907 379 BC HW: 6R0 907 379 AF
Component: ESP8.2i front H05 0002
Revision: --------
Coding: 210224E3217100B5842524E484D700401300
Shop #: WSC 00788 648 00255
VCID: 0008182F9710A43E5D-8054
1 Fault Found:
01299 - Diagnostic Interface for Data Bus (J533)
005 - No or Incorrect Basic Setting / Adaptation - Intermittent
Freeze Frame:
Fault Status: 00100101
Fault Priority: 0
Fault Frequency: 2
Reset counter: 162
Mileage: 63369 km
Time Indication: 0
Date: 2012.03.25
Time: 00:00:06
Freeze Frame:
Hex Value: 0x0007
Hex Value: 0x0002
Hex Value: 0x3023
Hex Value: 0x1497
Hex Value: 0x007F
Hex Value: 0x7F7F
Hex Value: 0x7FF9
-------------------------------------------------------------------------------
Address 08: Auto HVAC (J301) Labels: None
Part No SW: 6R0 820 045 N HW: 6R0 820 045 N
Component: Man AC H02 0202
Revision: 0003SH02
VCID: 397EB5CBB04A35F65A-806C
No fault code found.
-------------------------------------------------------------------------------
Address 09: Cent. Elect. (J519) Labels: None
Part No SW: 7E0 937 090 HW: 7E0 937 090
Component: BCM PQ25 Max4 H80 0736
Revision: B9080001 Serial number: 0771 060161479
Coding: 3CB02BBF08E10600923808006D2B0CD100C0412F60860000200000000000
Shop #: WSC 02737 534 00190
VCID: 68D8208F9B607C7EF5-803C
Subsystem 1 - Part No SW: 6R0 959 801 AB HW: 6R0 959 801 AB Labels: 6R0-959-801.CLB
Component: J386__TSG_FT 008 1611
Coding: 18BC30
Subsystem 2 - Part No SW: 6R0 959 802 AD HW: 6R0 959 802 AD Labels: 6R0-959-802.CLB
Component: J387__TSG_BT 008 1611
Coding: 08BC30
Subsystem 3 - Part No: 1K8 951 171 A
Component: DWA-Sensor 00 001 0103
Coding: 000000
Subsystem 4 - Part No: 1K0 951 605 C
Component: LIN BACKUP HO H03 1301
Coding: 000000
Subsystem 5 - Part No: 1K8 951 171 A
Component: DWA-Sensor 00 001 0103
Coding: 000000
Subsystem 6 - Part No SW: 5K0 959 542 C HW: 5K0 959 542 C
Component: E221__MFL-TAS H31 0037
Coding: 820000
Subsystem 7 - Part No SW: 6R0 959 811 G HW: 6R0 959 811 G
Component: J388__TSG_HL 008 1611
Coding: 08BC32
Subsystem 8 - Part No SW: 6R0 959 812 G HW: 6R0 959 812 G
Component: J389__TSG_HR 008 1611
Coding: 08BC32
1 Fault Found:
01504 - Bulb for License-Plate Light (X)
010 - Open or Short to Plus
Freeze Frame:
Fault Status: 01101010
Fault Priority: 3
Fault Frequency: 2
Reset counter: 122
Mileage: 63369 km
Time Indication: 0
Date: 2012.03.25
Time: 06:48:33
-------------------------------------------------------------------------------
Address 10: Park/Steer Assist (J446) Labels: 7E0-919-475.clb
Part No SW: 7E0 919 475 K HW: 56D 919 475
Component: PARKHILFE 8K H02 0106
Revision: -------- Serial number: 20251528901029
Coding: 100001
Shop #: WSC 12345 123 12345
ASAM Dataset: EV_VW57XParkAssis4K 001004
ROD: N/A
VCID: 3A7CAAC7BD4C3EEE53-806E
No ASAM data for: "EV_VW57XParkAssis4K" (VW25)
No fault code found.
-------------------------------------------------------------------------------
Address 15: Airbags (J234) Labels: 5K0-959-655.clb
Part No SW: 6R0 959 655 K HW: 6R0 959 655 K
Component: VW10Airbag022 H09 0020
Revision: -------- Serial number: 003GX011W0JJ
Coding: 003232
Shop #: WSC 00788 648 00255
ASAM Dataset: EV_AirbaVW10BPAVW250 A01001
ROD: EV_AirbaVW10BPAVW250_SE25.rod
VCID: 4A9CFA07EDACAE6EC3-801E
Crash sensor for side airbag; driver side:
Serial number: 3575HRB4059124B2F99H
Crash sensor for side airbag; front passenger side:
Serial number: 3585HRB4061131GQCOUS
Crash sensor for side airbag; rear; driver side:
Serial number: 3515RRB405P0VC0I5P0W
Crash sensor for side airbag; rear; passenger side:
Serial number: 3525RRB40510VC0IA9B9
No fault code found.
-------------------------------------------------------------------------------
Address 17: Instruments (J285) Labels: 5K0-920-xxx-17.clb
Part No SW: 6R0 920 871 A HW: 6R0 920 871 A
Component: KOMBI H03 0505
Serial number: 00000000000000
Coding: 140A01
Shop #: WSC 00788 648 00255
ASAM Dataset: EV_Kombi_UDS_VDD_RM09 A04113
ROD: EV_Kombi_UDS_VDD_RM09_SK35.rod
VCID: 346084FF9F28C89E89-8060
No fault code found.
-------------------------------------------------------------------------------
Address 19: CAN Gateway (J533) Labels: None
Part No SW: 7E0 909 901 HW: 7E0 937 090
Component: GW-K-CAN TP20 H80 0736
Revision: B9080001
Coding: 002200
Shop #: WSC 02737 534 00190
VCID: 68D8208F9B607C7EF5-803C
1 Fault Found:
01044 - Control Module Incorrectly Coded
000 - - - Intermittent
Freeze Frame:
Fault Status: 00100000
Fault Priority: 2
Fault Frequency: 1
Reset counter: 255
Mileage: 63369 km
Time Indication: 0
Date: 2012.03.25
Time: 06:48:01
-------------------------------------------------------------------------------
Address 25: Immobilizer (J334) Labels: 5K0-920-xxx-25.clb
Part No SW: 5K0 953 234 HW: 5K0 953 234
Component: IMMO H03 0505
Serial number:
Coding: 000000
Shop #: WSC 00000 000 00000
ASAM Dataset: EV_Immo_UDS_DVD_RM09 A03009
ROD: N/A
VCID: 6ADC5A878D6C4E6EE3-803E
No ASAM data for: "EV_Immo_UDS_DVD_RM09" (VW36 *)
No fault code found.
-------------------------------------------------------------------------------
Address 44: Steering Assist Labels: 6Q0-423-156.clb
Part No: 6R0 423 156 B
Component: LenkhilfeTRW V277
Coding: 11250
Shop #: WSC 00788
VCID: 2F6A8B93EA0EEB46F4-807A
1 Fault Found:
01288 - Terminal 30; Steering Assist
07-10 - Signal too Low - Intermittent
-------------------------------------------------------------------------------
Address 56: Radio (J503) Labels: None
Part No SW: 6RD 035 187 HW: 6RD 035 187
Component: Radio 517 5124
Revision: RB101000 Serial number: VWZZZ4Q5034465
Coding: 00000400040005
Shop #: WSC 12345 123 12345
VCID: 0400143F8708B81E79-8050
4 Faults Found:
00874 - Treble Speaker Front Left (R20)
011 - Open Circuit - Intermittent
Freeze Frame:
Fault Status: 00111011
Fault Priority: 5
Fault Frequency: 1
Reset counter: 122
Mileage: 63369 km
Time Indication: 0
Date: 2012.03.25
Time: 06:25:49
00875 - Treble Speaker Front Right (R22)
011 - Open Circuit - Intermittent
Freeze Frame:
Fault Status: 00111011
Fault Priority: 5
Fault Frequency: 1
Reset counter: 122
Mileage: 63369 km
Time Indication: 0
Date: 2012.03.25
Time: 06:25:49
00876 - Treble Speaker Rear Left (R14)
011 - Open Circuit - Intermittent
Freeze Frame:
Fault Status: 00111011
Fault Priority: 5
Fault Frequency: 1
Reset counter: 122
Mileage: 63369 km
Time Indication: 0
Date: 2012.03.25
Time: 06:25:49
00877 - Treble Speaker Rear Right (R16)
011 - Open Circuit - Intermittent
Freeze Frame:
Fault Status: 00111011
Fault Priority: 5
Fault Frequency: 1
Reset counter: 122
Mileage: 63369 km
Time Indication: 0
Date: 2012.03.25
Time: 06:25:49
End-------------------------(Elapsed Time: 02:49)--------------------------
I have already copied coding from 09-Central Electronics module and 19-CAN Gateway and restored original installation list.
These are some problems occurred:
- Instrument panel and engine switch on but no longer off (neither removing key)
- Headligts do not work properly
- Light dimmer no longer works
- Impossible to set up remote controllers because channel's value doesn't change (image attached)
- ciclo
- Bling Bling Diamond Member
- Posts: 7843
- Joined: Sun Feb 24, 2013 10:20 am
- Drives: 6R'13/G7.5'19
- Location: Earth ♥, sPAIN, Magiclands (Mordor).
- Contact:
Re: My polo 6r bifuel
http://wiki.ross-tech.com/wiki/index.ph ... l_Matching
(I copy and paste here)
Channel 001: Remote Control Matching
Start Matching new/additional Remote Controls by entering 0, then Test and Save the New Value.
Press and hold the Unlock button for at least one second on the Remote Control you want to add, the Blinkers will light up to confirm the Adaptation Process of each Remote Control.
So...
1st remote control ..... 01 Channel .... 0 ... test ... save ... process
2nd remote control ..... 01 Channel .... 0 ... test ... save ... process
and so on... 3rd, 4th, etc, remote controls.
Note: Do not worry, It's not a matter of understanding languages, many English speaking people also have difficulties to understand what is written in the ross-tech link.
(IMHO) I think that who wrote the text of the ross-tech link is a genius, I don't think it can be better explained.
Because some things will change when doing this remote controls adaptation process, report again of the permanent failures with a new autoscan.
What wiring have you installed so far?
- Bcm adaptation wiring
- Bixenon wiring
- Automatic lights wiring
- ...
The new BCM coding depends on it.
(I copy and paste here)
Channel 001: Remote Control Matching
Start Matching new/additional Remote Controls by entering 0, then Test and Save the New Value.
Press and hold the Unlock button for at least one second on the Remote Control you want to add, the Blinkers will light up to confirm the Adaptation Process of each Remote Control.
So...
1st remote control ..... 01 Channel .... 0 ... test ... save ... process
2nd remote control ..... 01 Channel .... 0 ... test ... save ... process
and so on... 3rd, 4th, etc, remote controls.
Note: Do not worry, It's not a matter of understanding languages, many English speaking people also have difficulties to understand what is written in the ross-tech link.
(IMHO) I think that who wrote the text of the ross-tech link is a genius, I don't think it can be better explained.
Because some things will change when doing this remote controls adaptation process, report again of the permanent failures with a new autoscan.
What wiring have you installed so far?
- Bcm adaptation wiring
- Bixenon wiring
- Automatic lights wiring
- ...
The new BCM coding depends on it.
- ciclo
- Bling Bling Diamond Member
- Posts: 7843
- Joined: Sun Feb 24, 2013 10:20 am
- Drives: 6R'13/G7.5'19
- Location: Earth ♥, sPAIN, Magiclands (Mordor).
- Contact:
Re: My polo 6r bifuel
Really? ... at this point of your installation?Franciswat wrote: ↑Thu Nov 02, 2017 12:22 am
I have a stupid question about wirings: every fuse has 2 pins with unique number, when I have to replace original 34b, 39b and 59b wires with new one which pin I have to replace?
Are you telling me that you don't know what to do if you expand/enlarge (to infinity and beyond... ) the WL2 image of the following link?
https://drive.google.com/file/d/0B2nv91 ... dDUlE/view
expand/enlarge https://drive.google.com/file/d/0B2nv91 ... sp=sharing
- Franciswat
- Silver Member
- Posts: 267
- Joined: Thu Sep 21, 2017 9:39 am
- Drives: 6R 1.6 Bifuel
- Location: Italy
Re: My polo 6r bifuel
I am Sorry ciclo i thought i could effort it correctly.
I Will check It again.
I am sad i am taking you so much time.
I Will check It again.
I am sad i am taking you so much time.